[ antrx.com ]
antrx technical discussion => antrx noise => Topic started by: coreyb317 on Mar 13, 2009, 10:31AM
-
Hey all...
I am tryin to intall a sub and amp into my new car. There are no RCA outputs from the head unit! I heard that you can wire in a high low converter, but also heard that the bass produced is not that good! Is this correct?
Whats the best way for me to wire this up ???
-
Hmmmm. I'm no expert on the subject so i'd wait for jono/sticky to reply, but heres what I think:
Most amps have what they call speaker-level inputs - that is you can wire speaker wire directly into the amp it's self. Main disadvantages of this is the low voltage of the signal and the inability to control the output independantly from the other speakers.
Also almost all amps these days come with built in hi/lo pass filters so that's not a big issue. Only problem I can see is where to source the signal from (assuimg you have 4 speakers) I don't think you can just piggyback off the rear speaker signals (could be wrong).
If it were me I'd goto my nearest car audio shop and buy a new headunit (no more then $150 for a basic mp3/cd with a set of rca outputs)
-
Yeah i wish i could but its for a Dodge Calibur and putting in a new head unit would mean customising the housing etc... I just wanna throw a sub in!
Is there any way for me to wire in some rca outputs to the stock head unit wiring loom???
-
Now that I think about it, yes!
something like these: http://www.davidnavone.com/cart.asp?24&cat=7
IIRC aerpro make these so drop into a supercheap, strathfeild etc. and get them to look it up in the catalouge for you.
EDIT: here you go - part numbers, http://www.aerpro.com.au/list.php?cat_no=07&cat_name=car%20audio%20accessories&cat_sno=147
I'm still not sure if you can just piggy back off the rear speaker lines or not though.
-
Prob wouldn't be that hard. I used one of those high low converter boxes on my car when I didn't have any RCA's. Just took it from the rear speakers, which I wasn't using. It sounded good too, enough bass to keep me happy.
So I reckon the box is just a few RCA's and some wire connections, Which means you could just solder some RCA's to the speaker wires (for a sub you only need one though, mono. Then get a splitter if you want) And plug it in.
I don't know if the speaker you took the signal from will still sound strong enough afterwards though. And I haven't done this at all. Just Speculating, so no guarantee it will work, but it's not like it's too hard to reverse. I say give it a shot, see what happens.
As an afterthought, Maybe there is something else in the box to boost the signal. but I sold mine so I can't have a look.
-
So I reckon the box is just a few RCA's and some wire connections, Which means you could just solder some RCA's to the speaker wires (for a sub you only need one though, mono. Then get a splitter if you want) And plug it in.
I don't know if the speaker you took the signal from will still sound strong enough afterwards though. And I haven't done this at all. Just Speculating, so no guarantee it will work, but it's not like it's too hard to reverse. I say give it a shot, see what happens.
As an afterthought, Maybe there is something else in the box to boost the signal. but I sold mine so I can't have a look.
Do Not Do This!
That would be the quickest and easiest way to blow up your amp. The converter box will change the signal from a high voltage speaker output to a line level rca signal. Much different from just wiring speakers to a rca plug.
That box jello suggested will work fine, and no problem running them off the rear speaker outs either.
-
My bad. Thought there might be something else in the box :-\, and one of my old amps had speaker wire inputs in them...
Anyway, just go get a converter box. easiest solution.
-
Thanks for the help fellas... Will give it a shot n report back!
-
If your amp has speaker level inputs use them, otherwise use a good quality line out converter.
You won't get great sound quality either way though.