Author Topic: Taking the Engine out.  (Read 5048 times)

0 Members and 1 Guest are viewing this topic.

Offline beejay85

  • antrx.com junior member
  • **
  • Posts: 68
  • Karma: +2/-0
  • Gender: Male
Taking the Engine out.
« on: Jun 14, 2009, 07:11PM »
So the time has come to take the engine out of my car. It has officially hit the 'Project car' status. I was wondering if anyone has any tips on how to take it out? i have access to a hoist and engine hoist thing (the little crane looking thing lol) so hopefully it should make it easier, but I was just seeing if anyone knows the best place to start etc etc.

Thanks Heaps

Offline Luke

  • 173kw @ all 4
  • sth. oz local moderator
  • antrx.com junkie
  • *****
  • Posts: 998
  • Karma: +17/-4
  • Gender: Male
Re: Taking the Engine out.
« Reply #1 on: Jun 14, 2009, 07:50PM »
It looks hard, but it's fairly straight forward. Take your radiator out, disconnect all your wiring loom. There's a couple of hard ones to get to, particularly the starter motor wiring and the knock sensor, the best way to get to these is through the driver side front wheel well. take your intercooler piping out, take your exhaust off, take the rear drive shaft out, pull your front drive shafts out. Take your clutch slave cylinder off aswell. There are a few other hoses and things to take off on the inlet manifold, oh and your air con compresor needs to be taken off... put a crate or a trolley under the car and lower it down until the engine is sitting on it, undo all your engine mounts and lift the car off of the engine...

Bit short, but if you have any questions I can go into further detail.
Jason reffering to the OzVR4 Forum... "Even their forum is slow" "FJ20.com on the other hand, yep that S12 does Mono's"

Offline Craazy

  • Resident Attesa Driver
  • antrx cruise monkey
  • post whore
  • *****
  • Posts: 2431
  • Karma: +29/-5
  • Gender: Male
  • Lovin it long time
Re: Taking the Engine out.
« Reply #2 on: Jun 16, 2009, 02:12AM »
what luke said. the pro's can do it in about 4 - 8 hours. last count it took me about 24 hours in my garage with no hoist, just an engine crane

best of luck with it


The Time Has Come To Battle It Out To The Death... SR24 vs KA24

The bluey must be revived to Life!!

Offline Luke

  • 173kw @ all 4
  • sth. oz local moderator
  • antrx.com junkie
  • *****
  • Posts: 998
  • Karma: +17/-4
  • Gender: Male
Re: Taking the Engine out.
« Reply #3 on: Jun 16, 2009, 09:05AM »
I reckon Jason and I have it down to about 2.5 hours, but we've done it a fair few times now.
Jason reffering to the OzVR4 Forum... "Even their forum is slow" "FJ20.com on the other hand, yep that S12 does Mono's"

Offline Habibosaurus

  • YouTube King
  • Global Moderator
  • antrx.com junkie
  • ****
  • Posts: 842
  • Karma: +23/-3
Re: Taking the Engine out.
« Reply #4 on: Jun 16, 2009, 04:59PM »
I reckon Jason and I have it down to about 2.5 hours, but we've done it a fair few times now.

Awaits a Today Tonight report with reports of rebirthing in several Western states on the rise...  ::)
Ill fight you. May even throw a bar of soap your way. Maybe a few wax strips and some clip on brembo brake calipers for your fooly sic civic.

Offline beejay85

  • antrx.com junior member
  • **
  • Posts: 68
  • Karma: +2/-0
  • Gender: Male
Re: Taking the Engine out.
« Reply #5 on: Jun 28, 2009, 09:01PM »
Hey thanks heaps for that. Finally got it out today... Hardest part seemed to be taking out the front drive shafts :S lol.  Other than that tho pretty spot on with your description. And surprisingly easy, figured there'd be a whole lot more to it.  Now the fun re-build begins .... lol?

Offline awd2.0t

  • antrx.com junior member
  • **
  • Posts: 98
  • Karma: +1/-0
Re: Taking the Engine out.
« Reply #6 on: Jun 21, 2010, 04:56PM »
It looks hard, but it's fairly straight forward. Take your radiator out, disconnect all your wiring loom. There's a couple of hard ones to get to, particularly the starter motor wiring and the knock sensor, the best way to get to these is through the driver side front wheel well. take your intercooler piping out, take your exhaust off, take the rear drive shaft out, pull your front drive shafts out. Take your clutch slave cylinder off aswell. There are a few other hoses and things to take off on the inlet manifold, oh and your air con compresor needs to be taken off... put a crate or a trolley under the car and lower it down until the engine is sitting on it, undo all your engine mounts and lift the car off of the engine...

Bit short, but if you have any questions I can go into further detail.

Sorry to drag up an old thread, but does the engine have to be dropped or can it be taken out the top?  How many hours should a mechanic charge for it?

Offline Budgie

  • Dr. B Udgie - AWD FTW
  • Administrator
  • post whore
  • *****
  • Posts: 9411
  • Karma: +131/-33
  • Gender: Male
  • U12-U13
Re: Taking the Engine out.
« Reply #7 on: Jun 21, 2010, 05:03PM »
Its MUCH easier to drop it out (tried the top once and changed... that sounded wrong!)

Taking it out the top would probably require gearbox removal in a U12/U13 I reckon.  But having always taken it out the bottom, I'm not really certain!

It took me 2 hours to pull the CA18DET from my car a few weeks ago.
dont piss me off with your pillarless shit captain snappy wrist

Offline SRU13

  • antrx.com junior member
  • **
  • Posts: 56
  • Karma: +2/-1
Re: Taking the Engine out.
« Reply #8 on: Jun 21, 2010, 06:21PM »
i just had mine out would have to come out thru the bottom and the gearbox must come out with it the effort of trying toget tot he bolts in the car would just add extra labour alot quicker todo on the ground

Offline awd2.0t

  • antrx.com junior member
  • **
  • Posts: 98
  • Karma: +1/-0
Re: Taking the Engine out.
« Reply #9 on: Jun 21, 2010, 09:17PM »
So does that mean it can't be done without a hoist?  If I was to take the job on at home with a mechanic mate what would be the best plan of attack?  Just run the car up on a ramps?

Offline Budgie

  • Dr. B Udgie - AWD FTW
  • Administrator
  • post whore
  • *****
  • Posts: 9411
  • Karma: +131/-33
  • Gender: Male
  • U12-U13
Re: Taking the Engine out.
« Reply #10 on: Jun 21, 2010, 09:41PM »
Yep, you could do it at home but try to figure out a way to take it out the bottom.
dont piss me off with your pillarless shit captain snappy wrist

Offline Luke

  • 173kw @ all 4
  • sth. oz local moderator
  • antrx.com junkie
  • *****
  • Posts: 998
  • Karma: +17/-4
  • Gender: Male
Re: Taking the Engine out.
« Reply #11 on: Jun 21, 2010, 09:46PM »
Yeah the engine definatelly has to come out the bottom, the gearbox sits underneath parts of the guards, it's a tight enough squeeze out the bottom. Gearbox definately wont come off with the engine in.
Jason reffering to the OzVR4 Forum... "Even their forum is slow" "FJ20.com on the other hand, yep that S12 does Mono's"

Offline Luke

  • 173kw @ all 4
  • sth. oz local moderator
  • antrx.com junkie
  • *****
  • Posts: 998
  • Karma: +17/-4
  • Gender: Male
Re: Taking the Engine out.
« Reply #12 on: Jun 21, 2010, 09:50PM »
Ramps wont be high enough. The engine is fairly tall. It can be done without a hoist. We've done it by lifting the car with a block and tackle. you need to take the handbrake of so you can move it around a bit. Just take you time, it's not as bad as it sounds.
Jason reffering to the OzVR4 Forum... "Even their forum is slow" "FJ20.com on the other hand, yep that S12 does Mono's"

Offline makudori

  • antrx.com junior member
  • **
  • Posts: 17
  • Karma: +0/-0
Re: Taking the Engine out.
« Reply #13 on: Jun 22, 2010, 11:42AM »
I used an engine crane to pull the body high enough, stands sitting on some big ass bricks held it in place while i moved the motor and mission out of the way.

I have pictures but not sure how to put them on this site

pm me if your  interested in looking at the pics
« Last Edit: Jun 22, 2010, 11:14PM by makudori »

Offline awd2.0t

  • antrx.com junior member
  • **
  • Posts: 98
  • Karma: +1/-0
Re: Taking the Engine out.
« Reply #14 on: Jun 23, 2010, 03:54PM »
When the engine is out to replace the clutch what else should be done?
 - Coolant hoses
 - Rear engine seal
 - Anything else?
 

Also in terms of fluids and gases what will I need to factor in?
 - I'm guessing coolant seems pretty obvious
 - Does the A/C need to be re-gassed?
 - Gearbox fluid etc.

Basically the plan is to supply the mechanic with all parts where possible.  So will need to get part numbers and such shortly.  In the short term mechanic just wants the list of what needs to be done for the quote.

Cheers.

Offline Craazy

  • Resident Attesa Driver
  • antrx cruise monkey
  • post whore
  • *****
  • Posts: 2431
  • Karma: +29/-5
  • Gender: Male
  • Lovin it long time
Re: Taking the Engine out.
« Reply #15 on: Jun 23, 2010, 08:55PM »
coolant, engine oil, gearbox oil, power steering fluid, clutch fluid and brake fluid

your ac will need to be regassed

check all your hoses before you put the engine back in to be on the safe side, check all your gaskets on the back of the engine for any oil seepage and replace as necessary. check your belts at the same time too

and give it a good clean before it goes back in and you will notice when its running if there are any other issues leak wise with a clean engine

good luck with it


The Time Has Come To Battle It Out To The Death... SR24 vs KA24

The bluey must be revived to Life!!

Offline Luke

  • 173kw @ all 4
  • sth. oz local moderator
  • antrx.com junkie
  • *****
  • Posts: 998
  • Karma: +17/-4
  • Gender: Male
Re: Taking the Engine out.
« Reply #16 on: Jun 23, 2010, 10:36PM »
Don't need to re-gas the AC, just unbolt the compressor off the block and leave it in the car.
Jason reffering to the OzVR4 Forum... "Even their forum is slow" "FJ20.com on the other hand, yep that S12 does Mono's"